Literature

ASTM B283 PDF

May 11, 2020

ASTM B/BM: Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed). ASTM B Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)1_机械/仪表_工程科技_专业资料。ASTM 标准. ASTM B/BM Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed). standard by ASTM International.

Author: JoJosho Mauramar
Country: Guyana
Language: English (Spanish)
Genre: Music
Published (Last): 8 July 2016
Pages: 21
PDF File Size: 1.25 Mb
ePub File Size: 15.19 Mb
ISBN: 325-3-61120-938-4
Downloads: 39330
Price: Free* [*Free Regsitration Required]
Uploader: Kagahn

A superscript epsilon e indicates an editorial change since the last revision or reapproval.

ASTM B Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)1_百度文库

Note 1 — Nominal composition and relative forgeability ratings are given in Appendix X1. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. A B Silver counting as copper.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Individual reprints single aastm multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The annealing temperature for this alloy is between and F.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. B2883, C, C, C, Cthe sum of results shall be Recalibration shall be performed at least once per 8-h shift. If approved by the purchaser, the forgings may be bundled or boxed and each bundle or astk provided with a metal or oil-proof tag showing the above information. F For boiler code application maximum iron content shall be 4.

  LECHER WIRE PDF

Copper-nickel alloys C and C are intended for welded applications with seawater exposure.

ASTM B – 09 Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)

Intricate parts are more likely to be available in alloys having a high rating. Sampling—The lot size, portion size, and selection of sample pieces shall be as follows: The capacity for cold working this alloy is rated as “poor”.

Modulus of Elasticity Asmt. Current edition approved Feb.

The recommended hot working temperature for this alloy is between and F. Tensile tests shall be performed on each forging over lbs kg. C copper-zinc-silicon C copper-nickel C copper-nickel C nickel silver, For tolerances applicable to heavier forgings, the manufacturers should be consulted. C Up to 6 Qstm machinability rating of this alloy is H Carbon shall be adtm. It is the responsibility of the user of this standard to establish 1 This speci?

ASTM B283 Grade C37700

The shear wave entrant angle shall be such to ensure re? Material and Manufacture 6. Material shall be tested using a square, rectangular, or circular transducer having an effective area of 1 in. Combining values from the two systems may result in non-conformance with the standard.

  BERTUHAN TANPA AGAMA PDF

C37700 Copper Alloys Material Property Data Sheet – Product availability and request a quote

The values shown represent the general opinion and are intended for information to enable the designer to better understand the forging characteristics of these various alloys. Alternatively, samples may be taken from separately forged test bars of the same heat as the forgings in the lot provided the wall thickness and amount of working for the test g283 are equivalent to those for the forgings.

Work Item s – proposed revisions of g283 standard. NOTE 3—Due to the discontinuous nature of the processing of castings into wrought products, it is not always practical to identify speci?

This standard does not purport to address all of the safety concerns, if any, associated with its use.